CCTV Mounts  (1,232)

Relevant Models : DC-D series

Relevant Models : DC-B series, DC-Z series

The outdoor-ready AXIS T91B67 Pole Mount has a 1.5" NPS threading for a wide range of Axis pendant kits for Axis fixed dome and panoramic cameras. Thanks to its impact-resistant and outdoor-proven material, the mount can be used in both indoor and outdoor environments. AXIS T91B67 is intended for poles with a diameter between 65–165 mm (2 1/2–6 1/2 in), and also for beams. It features 3/4" conduit side entries for protected cable runs, and a closed back with cable gasket for protection against insect infestation. The pole mount is tightened with two marine-grade (SS316L) stainless steel straps with TX30 screw interface for ease and secure installation.

180° tilt.  Interchangeable parts allow for customisation in 24 different combinations.

Aluminium wall mount compatible with all Axis outdoor fixed box cameras and housings IK10-rated, offers protection against impact and vandal acts Corrosion resistant according to NEMA 4X rating

Ideal for retail and commercial environments, where a fixed dome or a fixed box camera need to be installed under high ceilings The telescopic functionality allows the installer to easily and securely adjust the length of extension between 1m/3.2ft to 1.8m/6ft at 10 cm/4” intervals The base of the telescopic mount is compatible with AXIS T94F01P Conduit Back Box for a safe cabling through 1/2” (M20) conduit pipes The lightweight and robust ceiling mount can also be installed horizontally on walls when secured with AXIS Safety Wire Suitable for indoor use Compatible with Axis pendant kits and camera holders with 3/4” conduit interface

Cost-effective mount for Axis fixed dome cameras Recessed ceiling installation made quick and easy Enables sleek and discreet video surveillance

Made for parapet and wall installations when the requirement is to place the camera further out from the wall Its ability to swivel 180 degrees on its own axis, allows for easy and safe mounting/maintenance of the camera from a rooftop Intended for outdoor fixed and PTZ dome cameras supporting 1.5” NPS thread Corrosion protected

Designed for Axis PTZ and multi-sensor cameras Flexible installation using the IDC connector Built-in IP66 RJ45 connector Suitable for wall and pole mounting- Protection against impact, water, dust and corrosion

Designed for discreet installation in drop and overhang ceilings Compatible with the bullet cameras from AXIS M20 Network Camera Series Applicable for indoor environments as well as outdoor use in soffits Also suitable for installation in air-handling (plenum) spaces as the enclosure is made of metal alloy with a 1/2” (M20) conduit hole for protected cable routing

Corrosion resistant to seawater and chemicals 1.5'' NPS Outdoor-ready Marine grade stainless steel (SS 316L) Ideal for stainless steel fixed dome cameras

Corrosion resistant to seawater and chemicals 1.5'' NPS Outdoor-ready Marine grade stainless steel (SS 316L) Ideal for stainless steel fixed dome cameras

An aluminium parapet mount, which includes AXIS T94A01D Pendant Kit (only used in combination with PTZ cameras) and AXIS T91A6 Pipe Seal Also compatible with Axis pendant kits with 1.5” NPS inner thread, and Axis ACI 3/4” conduit adapters The cables can be routed through the back, or from the side by using a conduit connection For indoor and outdoor use Vandal resistance with IK10

Indoor and outdoor use – pole installation Protection against water and dust Compatible with AXIS T92F10 Outdoor Housing Easy to install

IS50-P is an outdoor pendant mount for Pelco IS50 and IS51

An aluminium wall mount suitable for Axis positioning cameras and positioning units Compatible with Axis ACI 3/4” conduit adapters, and offers six cable entries Cables can be routed through the back or, by using a conduit connection, from each side or from the bottom For indoor and outdoor use Impact-resistant (IK10)

For outdoors and indoors Robust and safe installation Support for Axis PTZ domes and fixed domes with 1.5” NPS thread Flexible length, up to 5 m (197 in) with extension pipes Swivel action with a ±45° pivot angle

An aluminium wall mount with a 1.5″ NPS thread Compatible with Axis fixed dome pendant kits and Axis ACI 3/4” conduit adapters The cables can be routed through the back hole, or from the side by using a conduit connection Includes AXIS T91A6 Pipe Seal Indoor and outdoor use Robust and safe installation Vandal resistance with IK10

Designed for both indoor and outdoor use Available in two versions with different lengths of marine-grade (SS316L) stainless steel straps One version for poles with diameter between 50–150 mm (2–6 in), and one for poles with diameter between 100-410 mm (4–16 in) in diameter Compatible with Axis fixed dome or fixed bullet cameras

AXIS T91B57 Pole Mount Grey is a versatile and robust pole mount that can be used under harsh outdoor conditions. It is designed for use with selected AXIS T91 Wall Mounts and AXIS T98A Cabinet Series.  One pair of AXIS Stainless Steel Straps 1450 mm (57 in) with TX30 screw interface is included.

Designed for PTZ and multi-sensor cameras Room for connectivity devices, midspans (not included) and service loop Protection against impacts, water, dust and corrosion Pre-mounted IP66 RJ45 connector Re-use existing holes

Enables sleek, elegant and discreet recessed ceiling installations together with AXIS M5525-E PTZ network camera Suitable for air-handling spaces in indoor installations as the back box is made of metal and has a 3/4” (M25) hole for protected cable-runs in conduits Indoor and outdoor use

Suitable for wide range of pole diameters Safe and easy to install IK10-rated vandal resistance NEMA 4X-rated corrosion protection Axis stainless steel straps included

Suitable for all Axis fixed dome cameras compatible with 1.5” NPS threaded Axis pendant kits Can be used in both indoor and outdoor environments Intended for poles with a diameter between 65–165 mm (2 1/2–6 1/2 in), and also for beams Features 3/4" conduit side entries for protected cable runs, and a closed back with cable gasket for protection against insect infestation Impact-resistant to prevent vandalism

Marine-grade stainless steel (SS 316L) High corrosion resistance against salt water and chemicals Outdoor pendant mounting Suitable for stainless steel fixed domes cameras

Made of stainless steel 1.4404 (316L) Resistant to corrosion Sturdy and safe Compatible with ExCam XPT Q6055  

Protection against water and dust Flexible cable routing Easy to install Powder-coated aluminum

Electropolished stainless steel (316L) For poles with a diameter of 90 to 120 mm (3.5 to 4.7 in) Weight 4.2 kg (9.3 lb)

Robust and safe pole installation Suitable for indoor and outdoor use Impact-resistant to prevent vandalism Cable gasket to prevent insect infestation Support for 1.5" NPS threaded Axis pendant kits

AXIS T91B57 Pole Mount is a versatile and robust, high-quality pole mount. While it can be used indoors, it’s particularly appropriate for outdoor installations under harsher conditions. The high-quality pole mount is designed for use with selected AXIS T91 wall mounts and AXIS T98A cabinet series. It is easily adjustable to fit poles with a diameter between 100–410 mm (4–16 in).

Marine-grade stainless steel (SS 316L) High corrosion resistance against salt water and chemicals Indoor and outdoor pole mounting Suitable for stainless steel fixed domes cameras

Marine-grade stainless steel (SS 316L) High corrosion resistance against salt water and chemicals Indoor pendant mounting Suitable for stainless steel fixed domes cameras

Made of stainless steel EN 1.4404 (ASTM 316L) Resistant to corrosion Sturdy and safe Compatible with ExCam XF M30 cameras

Swivel movement of ±90-degree pan and ±45-degree tilt Suitable for marine and heavy industrial applications Easy to install Electropolished stainless steel (SS 316L)

Made of stainless steel 1.4404 (316L) For pole diameters from 110 to 150 mm (4.3 to 5.9 in) Resistant to corrosion Sturdy and safe Compatible with ExCam XPT Q6055

Suitable for wide range of pole diameters Safe and easy to install IK10-rated vandal resistance NEMA 4X-rated corrosion protection Axis stainless steel straps included

AXIS T94V01C Dual Camera Mount is a highly versatile accessory that allows back-to-back installation of two Axis cameras for panoramic coverage. It is compatible with a wide range of Axis network cameras, including dome cameras, box cameras, and bullet cameras. It can be easily combined with diverse Axis mounting accessories with 1.5” NPS threaded interface, for mounting on walls, poles, and under ceilings. AXIS T94V01C Dual Camera Mount has an IK10 rating for impact resistance, which safeguards it against vandalism. It is suitable for both indoor and outdoor use.

For outdoors and indoors Robust and safe installation Support for Axis PTZ domes and fixed domes with 1.5” NPS thread Flexible length, up to 5 m (197 in) with extension pipes Swivel action with a ±45° pivot angle

An aluminium ceiling mount that includes AXIS T94A01D Pendant Kit (only used in combination with PTZ cameras) and AXIS T91A6 Pipe Seal Also compatible with Axis pendant kits with 1.5" NPS inner thread, and Axis ACI 3/4" conduit adapters The cables can be routed through the back, or from the side by using a conduit connection For indoor and outdoor use Vandal resistance with IK10

Allows back-to-back installation of two Axis cameras for panoramic coverage Compatible with a wide range of Axis network cameras, including dome cameras, box cameras, and bullet cameras Can be easily mounted to diverse Axis mounting accessories with 1.5” NPS threaded interface, for mounting on walls, poles, and under ceilings IK10 rated for impact resistance, which safeguards it against vandalism Suitable for both indoor and outdoor use